| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix OOB read/write from unvalidated DataOffset in coalesce_t2()
coalesce_t2() computes data pointers directly from server-supplied
DataOffset fields with no validation against buffer bounds:
data_area_of_tgt = (char *)&pSMBt->hdr.Protocol +
get_unaligned_le16(&pSMBt->t2_rsp.DataOffset);
data_area_of_src = (char *)&pSMBs->hdr.Protocol +
get_unaligned_le16(&pSMBs->t2_rsp.DataOffset);
data_area_of_tgt += total_in_tgt;
...
memcpy(data_area_of_tgt, data_area_of_src, total_in_src);
A small DataOffset can push a pointer below the actual byte area,
overwriting header fields; a large one can push it past the buffer
end, causing out-of-bounds heap reads (source) or writes (target).
The BCC overflow guard does not prevent this: BCC reflects how much
data is present, while DataOffset controls where in the buffer it
starts.
The "validate target area" comment present since the function was
first written in 2005 was a placeholder that was never implemented.
Add lower- and upper-bound checks for both data pointers before the
memcpy, and before any target header fields are modified. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix use-before-check of ReparseDataLength in reparse_buf_ptr()
reparse_buf_ptr() reads buf->ReparseDataLength before checking that
count covers the full fixed header:
buf = (struct reparse_data_buffer *)((u8 *)io + off);
len = sizeof(*buf); /* 8 bytes */
rdlen = le16_to_cpu(buf->ReparseDataLength); /* offset 4, 2 bytes */
if (count < len || count < rdlen + len) /* check comes after */
struct reparse_data_buffer has ReparseDataLength at offset 4. If a
server returns OutputCount < 6, the read at offset 4-5 reaches past
the end of the received data. The off+count bounds against iov_len
were already validated, but that does not protect against count being
smaller than sizeof(*buf).
Split the check: verify count >= sizeof(*buf) before reading
ReparseDataLength, then verify count covers the data region. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: reject a tree connect response whose byte count is too small
CIFSTCon() bounds its strnlen() over the byte area with the server's
ByteCount minus two, which for ByteCount 0 or 1 goes negative as an int
and converts to a huge size_t. The later subtraction wraps the __u16
bytes_left, and that is what bounds cifs_strndup_from_utf16(): a bound of
up to 65535 against a ~16 KB cifs_req_poolp object runs off the end of the
slab object, and the bytes reach userspace through tcon->nativeFileSystem
in /proc/fs/cifs/DebugData.
Reject a byte area too small for what the parser consumes. Two bytes is
the least it can consume, and no conformant response carries fewer. The
new trace point is the 129th smb_eio_trace entry, which __mode(byte)
cannot represent, so the attribute goes with it. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: sony: fix UAF of ghl_poke_timer / ghl_urb at driver unbind
For GHL (Guitar Hero Live) dongles, sony_probe() arms a periodic timer:
ghl_magic_poke() (the timer callback) submits sc->ghl_urb, and the URB
completion ghl_magic_poke_cb() re-arms the timer with mod_timer().
sony_remove() drained the timer with timer_delete_sync() and then freed
the URB with usb_free_urb():
timer_delete_sync(&sc->ghl_poke_timer);
usb_free_urb(sc->ghl_urb);
timer_delete_sync() does not block re-arming, and while the URB is in
flight the timer is not pending, so the sync delete is a no-op. A URB
completion that runs after the delete re-arms the timer, and usb_free_urb()
only drops a reference -- it does not kill an in-flight URB. sc is
allocated with devm_kzalloc() and freed once sony_remove() returns, so the
re-armed ghl_poke_timer (embedded in sc) then fires on freed memory, a
use-after-free from timer softirq. This is a disconnect/rmmod race.
Poison the URB first, then shut the timer down, before freeing the URB.
usb_poison_urb() kills any in-flight URB and permanently rejects further
submissions, so a poke timer that is still pending cannot re-submit the
URB from ghl_magic_poke() in the window before timer_shutdown_sync() runs.
usb_kill_urb() would not suffice: it only cancels the in-flight URB and
leaves it submittable once it returns, so the pending timer could
re-submit it and put a fresh URB in flight over the freed sc.
timer_shutdown_sync() then drains any last callback and blocks re-arming.
The probe error path is unaffected: it is only reached before the timer
is armed.
Reproduced under KASAN on next-20260710 via dummy_hcd + raw-gadget
emulation of the GHL PS4 dongle (VID 0x1430 / PID 0x07bb): hid-sony binds
and arms the poke timer, the poke URB is held in flight, the driver is
unbound (freeing sc), then the URB is released. The completion re-arms the
timer on the freed sc, and the re-armed timer fires ~8 s later:
BUG: KASAN: slab-use-after-free in ghl_magic_poke+0x98/0xb0
Read of size 8 at addr ffff88810b02fd50 by task swapper/0/0
ghl_magic_poke+0x98/0xb0
call_timer_fn+0x35/0x2b0
__run_timers+0x69c/0x9a0
run_timer_softirq+0x173/0x2a0
Allocated by task 169: sony_probe
Freed by task 338: devres_release_group <- hid_device_remove (sony_remove)
Found by 0sec (https://0sec.ai) using automated source analysis. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: universal-pidff: stop the device when force-feedback init fails
universal_pidff_probe() starts the device with hid_hw_start() and then, if
force-feedback initialisation fails, returns the error through a label that
only does "return error". The device is left started.
The HID core does not unwind on the driver's behalf. __hid_device_probe()
releases the devres group, closes the report and clears hdev->driver:
if (ret) {
devres_release_group(&hdev->dev, hdev->devres_group_id);
hid_close_report(hdev);
hdev->driver = NULL;
}
The hidraw character device that hid_hw_start() registered through
hid_connect() is allocated with kzalloc() and added with cdev_device_add(),
so it is not devres-managed and survives that. With hdev->driver NULL,
hid_device_remove() skips hid_hw_stop() as well, because it only unwinds
while a driver is still attached. The registration therefore outlives the
device on both paths.
Opening the surviving /dev/hidrawX writes into freed memory. KASAN reports
a use-after-free write from hidraw_open() -> hid_hw_open() -> the
transport's open callback, which takes a spinlock inside the freed object.
A descriptor that carries a PID usage page and no input reports is enough:
hidraw claims the device so hid_hw_start() succeeds, while hid->inputs
stays empty so force-feedback init fails. The other failure returns in
hid_pidff_init_with_quirks() - no output reports, an allocation failure,
pidff_init_fields(), pidff_check_autocenter(), an unusable effect count,
input_ff_create() - all reach the same label.
Stop the device on that path. hid-dr.c and hid-emsff.c, which start the
device with the same HID_CONNECT_DEFAULT & ~HID_CONNECT_FF mask, already do
this. The two earlier gotos must keep returning without hid_hw_stop(),
since neither has a started device, so give the path that fails after the
start its own label.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com> |
| In the Linux kernel, the following vulnerability has been resolved:
HID: mcp2221: clear rxbuf after I2C/SMBus transfer completes
mcp_i2c_smbus_read() stores the caller-supplied buffer pointer in
mcp->rxbuf for the duration of a transfer but never clears it when the
transfer finishes or times out. Once the caller frees or reuses the
buffer, mcp->rxbuf becomes a dangling pointer. A delayed or spurious
MCP2221_I2C_GET_DATA report can then drive mcp2221_raw_event() to
memcpy device data into the freed memory, causing a write
use-after-free.
Route all return paths through a single exit point that clears
mcp->rxbuf and mcp->rxbuf_size, so that the existing !mcp->rxbuf guard
in the raw_event handler can reject any report arriving after the
transfer has ended. |
| In the Linux kernel, the following vulnerability has been resolved:
ext2: Fix lost inode updates for IS_SYNC inodes
ext2_setsize() and ext2_xattr_set2() had a construct like:
if (IS_SYNC(inode)) {
sync_inode_metadata(inode, 1);
} else {
mark_inode_dirty(inode);
}
which leads to lost inode updates for IS_SYNC inodes because
sync_inode_metadata() does anything only if the inode is already dirty
and hence inode updates may be simply lost. Fix the problem by
unconditionally marking the inode dirty and *then* call
sync_inode_metadata(). |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Disable preemption in __bpf_get_stack
get_perf_callchain() returns a per-CPU perf_callchain_entry buffer and
releases its recursion slot via put_callchain_entry() before returning,
so nothing keeps the entry reserved while __bpf_get_stack() consumes
it below.
A preemptible BPF program (e.g. a non-sleepable raw tracepoint program
on a PREEMPT kernel, which runs under migrate_disable() but not
preempt_disable()) can be scheduled out between obtaining the entry
and the copy. Another task scheduled on the same CPU then reuses the
same per-CPU buffer and overwrites trace->nr with a larger value.
copy_len is then computed from the inflated trace->nr and can exceed
the caller's buffer, causing an out-of-bounds write in the memcpy()
and in the build_id path.
The rcu_read_lock() taken here alone does not prevent this. It is
only taken on the may_fault path, and under CONFIG_PREEMPT_RCU it does
not disable preemption; it merely keeps perf's callchain buffer array
alive (freed via call_rcu()) and does nothing to stop another task
from reusing the entry.
Disable preemption around obtaining the callchain entry and copying
it into the caller's buffer, so the entry cannot be reused underneath
us and trace->nr stays bounded by max_depth. Build ID resolution may
fault and is therefore deferred until after preemption is re-enabled;
by then the instruction pointers have already been copied into buf,
so it operates only on that private copy. Note, preempt_disable() also
subsumes the buffer-lifetime guarantee the rcu_read_lock() provided,
since a preempt-disabled section is an RCU read-side critical section
for the callchain buffers' call_rcu() reclaim.
[ changed Fixes: commit ] |
| In the Linux kernel, the following vulnerability has been resolved:
dm array: validate array block headers on read
array_block_check() validates blocknr and csum and nothing else, while
node_check(), next to it, has bounded the structural fields since both
were written. dm_array_cursor_next() takes its loop bound from the
on-disk nr_entries and element_at() is unguarded pointer arithmetic, so
a count larger than the block holds keeps the cursor in one block while
the index grows past it and the read walks off the dm-bufio buffer --
dm_cache_load_mappings() drives it once per cache block at activation.
Check the header against itself: reject a zero value_size, require
max_entries to equal calc_max_entries() for that value_size and block
size, and require nr_entries to fit. Equality rather than an upper bound,
since a count below the real capacity trips BUG_ON() in fill_ablock() and
trim_ablock(). Metadata dm-array writes satisfies all three. |
| In the Linux kernel, the following vulnerability has been resolved:
cpufreq: apple-soc: Fix OPP table cleanup
apple_soc_cpufreq_init() adds OPP tables from firmware, but
some failure paths do not remove them. The driver also uses
dev_pm_opp_remove_all_dynamic(), which is not the right cleanup
helper for OPP tables loaded from firmware.
Use the cpumask OPP helper after the policy CPU mask has been
populated. Pair it with the matching cpumask remove helper on
failure paths and in apple_soc_cpufreq_exit(). This also removes
the separate dev_pm_opp_set_sharing_cpus() call, as the cpumask
helper loads the DT OPP tables for all CPUs in the policy. |
| In the Linux kernel, the following vulnerability has been resolved:
jbd2: bound shrinker scans by examined checkpoint buffers
The jbd2 shrinker currently accounts only checkpoint buffers that it
successfully releases against nr_to_scan. Busy buffers therefore do not
consume the scan budget.
If a checkpoint transaction contains mostly busy buffers, the shrinker
can scan its entire checkpoint list while holding journal->j_list_lock.
Large checkpoint lists can result in excessive lock hold times and leave
other CPUs spinning on j_list_lock, causing soft lockups or RCU stalls.
Pass nr_to_scan into journal_shrink_one_cp_list() and decrement it for
every buffer examined, including busy buffers. Pass NULL from checkpoint
cleanup paths so their existing full-list behavior is preserved.
This restores the scan-budget semantics that existed before
journal_shrink_one_cp_list() was changed to always scan a complete
checkpoint list. |
| In the Linux kernel, the following vulnerability has been resolved:
jbd2: check need_resched() when skipping busy checkpoint buffers
journal_shrink_one_cp_list() skips busy checkpoint buffers when called
with JBD2_SHRINK_BUSY_SKIP. The continue statement on this path also
skips the need_resched() check at the end of the loop body.
Consequently, when a checkpoint list contains mostly busy buffers, the
shrinker can walk the entire list while holding journal->j_list_lock,
even when a reschedule has been requested. Large checkpoint lists under
memory pressure can therefore cause long lock hold times and leave other
CPUs spinning on j_list_lock, resulting in soft lockups or RCU stalls.
Route the busy-buffer path through the need_resched() check so that the
shrinker can release j_list_lock and reschedule promptly, restoring
parity with the clean-buffer path, which already checks need_resched().
This does not change which checkpoint buffers are eligible for removal. |
| In the Linux kernel, the following vulnerability has been resolved:
ip: orphan prefetched skbs before multicast forwarding
IPv4 and IPv6 input preserve an skb->sk association installed by
bpf_sk_assign() so that local delivery can use the selected socket under
RCU. Both address families can also prefetch a socket in UDP early demux.
In both paths (BPF and UDP early demux) a reference is not guaranteed to
be held on the socket.
When a multicast packet is not locally deliverable, IPv6 hands the
original skb to ip6_mr_input(). IPv4's ip_mr_input() similarly keeps the
original skb when local delivery is not needed. Either path can put the
skb on an unresolved multicast route queue or forward it after the
receive-side RCU section ends.
After the prefetched socket is destroyed, a later skb free invokes
sock_pfree() and dereferences the stale skb->sk. Orphan the skb before
each non-local multicast forwarding path. Local delivery retains the
original skb; the existing skb_clone() calls provide multicast forwarding
with a socket-free clone. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: rpl: fix NULL dereference of idev in ipv6_rpl_srh_rcv()
ipv6_rpl_srh_rcv() dereferences idev from __in6_dev_get() without a NULL
check when reading idev->cnf.rpl_seg_enabled.
When the device's MTU drops below IPV6_MIN_MTU, addrconf_ifdown() clears
dev->ip6_ptr through RCU_INIT_POINTER(). A packet that passed the idev
check in ip6_rcv_core() can then reach ipv6_rpl_srh_rcv() with
dev->ip6_ptr already NULL.
Reproduced by flooding the receiving interface with ping6 traffic while
flapping its MTU between 1500 and 1200:
BUG: KASAN: null-ptr-deref in ipv6_rpl_srh_rcv+0xb3/0x1070
Read of size 4 at addr 00000000000006b4 by task ping6/394
CPU: 2 UID: 0 PID: 394 Comm: ping6 Not tainted 7.2.0-rc7-micro-vm-dev-00095-g24ef02f934ee #240 PREEMPT(full)
Call Trace:
<IRQ>
kasan_report+0xc6/0x100
ipv6_rpl_srh_rcv+0xb3/0x1070
ip6_protocol_deliver_rcu+0x759/0x9a0
ip6_input_finish+0xa8/0x1b0
ip6_input+0xe1/0x490
ipv6_rcv+0x33d/0x460
__netif_receive_skb_one_core+0xd6/0x130
process_backlog+0x2cc/0xa00
__napi_poll.constprop.0+0x56/0x270
net_rx_action+0x327/0x730
handle_softirqs+0x11e/0x630
do_softirq+0xb3/0xf0
</IRQ>
Both ipv6_rpl_srh_rcv() and ipv6_srh_rcv() are called only from
ipv6_rthdr_rcv(), which already has an idev lookup.
Fix the NULL dereference on the RPL path by checking idev in
ipv6_rthdr_rcv(), before it calls either function. The callees take idev as
an argument and no longer call __in6_dev_get(), so the packet is now
dropped in one place, with SKB_DROP_REASON_IPV6DISABLED on both paths. |
| In the Linux kernel, the following vulnerability has been resolved:
params: fix charp corruption on allocation failure
param_set_charp() stores charp parameters in allocated memory after slab is
available, and releases the previous value when the parameter is updated.
The previous value is released before the replacement allocation succeeds.
If kmalloc_parameter() fails, the setter returns -ENOMEM with the parameter
left as NULL.
Failing zswap's compressor update before zswap is initialized can later
trigger:
BUG: kernel NULL pointer dereference, address: 0000000000000000
RIP: 0010:strcmp+0x10/0x30
Call Trace:
zswap_setup+0x3b1/0x490
zswap_enabled_param_set+0x5b/0xa0
param_attr_store+0x93/0xe0
module_attr_store+0x1c/0x30
kernfs_fop_write_iter+0x116/0x1f0
Allocate and copy the replacement first, then replace the parameter value
only after allocation succeeds. |
| In the Linux kernel, the following vulnerability has been resolved:
SUNRPC: fix gssx_dec_option_array error path bugs
Four coupled defects in the gssx XDR option-array decoder make the
error paths unsafe: a NULL deref in the caller, a refcount leak on
the decoded group_info, and a latent use-after-free that the leak
fix would otherwise expose.
gssx_dec_option_array() sets oa->count = 1 before allocating
oa->data. If that allocation fails, -ENOMEM is returned with
oa->count == 1 and oa->data == NULL. All other error paths jump
to free_oa: which frees oa->data and NULLs it but also leaves
oa->count == 1. The caller trusts the count:
gssp_accept_sec_context_upcall()
gssx_dec_accept_sec_context()
gssx_dec_option_array() /* fails, count=1 data=NULL */
data = res.options.data[0].value /* NULL deref */
Independently, free_creds: releases the partially decoded svc_cred
with a bare kfree(creds). gssx_dec_linux_creds() installs a
groups_alloc() result into creds->cr_group_info; that object is
kvmalloc-backed and refcounted, and only put_group_info() reaches
kvfree(). A plain kfree(creds) drops the wrapper and leaks the
group_info allocation.
The natural fix for the leak is to call free_svc_cred(creds) before
kfree(creds), but free_svc_cred() invokes put_group_info() on
creds->cr_group_info unconditionally when non-NULL. The existing
out_free_groups: path in gssx_dec_linux_creds() already called
groups_free() on that pointer without clearing it, so once
free_svc_cred() is wired in, the subsequent put_group_info() would
touch freed memory.
Fix all four together:
- Move the oa->count = 1 assignment below the oa->data allocation
so it is never set when oa->data is NULL.
- Reset oa->count to 0 at free_oa: so count and data stay
coherent and the caller sees an empty option array.
- Call free_svc_cred(creds) before kfree(creds) at free_creds:
so the refcounted cr_group_info is released. free_svc_cred()
either NULL-guards each field explicitly (cr_group_info has
an if() check) or delegates to a helper that is NULL-safe
itself (kfree for the string fields, gss_mech_put() which
guards with if(gm) at gss_mech_switch.c:342), so it is safe
to call on a partially decoded svc_cred where only
cr_uid/cr_gid/cr_group_info have been written and everything
else is zero from kzalloc.
- In gssx_dec_linux_creds()'s out_free_groups: path, release
cr_group_info with put_group_info() rather than groups_free()
so the teardown matches free_svc_cred()'s refcount-aware path,
and clear the pointer so a later free_svc_cred() on the same
creds does not release it a second time. |
| In the Linux kernel, the following vulnerability has been resolved:
sunrpc: fix use-after-free in __rpc_clnt_handle_event and __rpc_clnt_remove_pipedir
Normal client creation goes through rpc_setup_pipedir(), which records
clnt->pipefs_sb, but the mount-event path in __rpc_clnt_handle_event()
calls rpc_setup_pipedir_sb() directly and never refreshes that field.
The umount path also removes the directory without clearing
clnt->pipefs_sb.
After a late pipefs mount or any remount, rpc_clnt_remove_pipedir()
compares the current superblock against a stale pipefs_sb pointer and
skips cleanup, leaving pipefs dentries whose inode private data still
points at a freed rpc_clnt, leading to a potential use-after-free during
subsequent rpc_info_open() or rpc_show_info() calls.
Fix this by properly updating clnt->pipefs_sb upon mount events and
clearing it during unmount or failure paths. |
| In the Linux kernel, the following vulnerability has been resolved:
SUNRPC: reject duplicate CREDS_VALUE options
gssx_dec_option_array() walks the wire-supplied option array and, for
every entry whose name matches CREDS_VALUE, calls
gssx_dec_linux_creds() on the same struct svc_cred. That helper
unconditionally installs a fresh groups_alloc() result into
creds->cr_group_info without releasing whatever pointer was already
there:
for (i = 0; i < count; i++) {
... decode name ...
if (length == sizeof(CREDS_VALUE) &&
memcmp(p, CREDS_VALUE, sizeof(CREDS_VALUE)) == 0) {
err = gssx_dec_linux_creds(xdr, creds);
...
}
}
A reply that carries two CREDS_VALUE entries therefore overwrites
cr_group_info on the second iteration and orphans the group_info
allocated by the first call. The earlier free_creds path only
releases the last cr_group_info via free_svc_cred(), so the first
allocation's refcount stays at one and its kvmalloc-backed storage
is leaked. No in-tree caller of gssp_accept_sec_context_upcall()
expects more than one CREDS_VALUE per reply.
Fix by tracking whether a CREDS_VALUE option has already been
decoded and returning -EINVAL on any subsequent match, so the
free_creds path releases the single group_info that was installed. |
| In the Linux kernel, the following vulnerability has been resolved:
SUNRPC: Reject short RFC 4121 MIC tokens in gss_krb5_verify_mic_v2
gss_krb5_verify_mic_v2() reads the token ID at ptr[0..1], the flags
byte at ptr[2], and padding at ptr[3..7], then passes
ptr + GSS_KRB5_TOK_HDR_LEN and cksum_len to gss_krb5_mic_build_sg().
None of these accesses check read_token->len first.
The minimum safe token size is GSS_KRB5_TOK_HDR_LEN (16) plus
ctx->krb5e->cksum_len (12-24, depending on the enctype). All callers
accept shorter tokens from the wire:
- gss_unwrap_resp_integ() enforces only an upper bound
(offset + len <= rcv_buf->len) before allocating
mic.data = kmalloc(len) and passing it to gss_verify_mic().
A malicious NFS server can therefore supply a short checksum
opaque, producing a small slab allocation that the Kerberos MIC
verifier reads past.
- gss_validate() enforces only len <= RPC_MAX_AUTH_SIZE (400)
before passing the wire-supplied length to
gss_validate_seqno_mic(), which constructs a mic xdr_netobj
and calls gss_verify_mic().
- svcauth_gss_verify_header() enforces only
checksum.len >= XDR_UNIT (4 bytes) before dispatching to
gss_verify_mic().
- svcauth_gss_unwrap_integ() checks only that the checksum fits
in gsd->gsd_scratch.
Add a length guard at the top of gss_krb5_verify_mic_v2(), before any
ptr[] access or scatterlist construction. Well-formed MIC tokens from
gss_krb5_get_mic_v2() already have exactly GSS_KRB5_TOK_HDR_LEN +
cksum_len bytes, so valid traffic is unaffected. |
| In the Linux kernel, the following vulnerability has been resolved:
svcrdma: Clear sc_cm_id when ADDR_CHANGE replacement fails
When svc_rdma_listen_handler() handles RDMA_CM_EVENT_ADDR_CHANGE,
it creates a replacement listener cm_id and returns 1, telling
the CM core to destroy the old one. If the replacement allocation
fails, sc_cm_id still points at the old cm_id that the CM core is
about to destroy. Any subsequent dereference of sc_cm_id --
such as svc_rdma_detach()'s rdma_disconnect() call -- is a
use-after-free.
NULL sc_cm_id on the failure path and guard svc_rdma_detach()'s
rdma_disconnect() call against NULL so that the listener can
be torn down safely when the server shuts down. |
