| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
macsec: don't read an unset MAC header in macsec_encrypt()
macsec_encrypt() reads the Ethernet header via eth_hdr(skb)
(skb->head + skb->mac_header) to memmove() the 12 source/destination MAC
bytes forward and make room for the SecTAG.
On the AF_PACKET SOCK_RAW + PACKET_QDISC_BYPASS transmit path the skb
reaches the macsec ndo_start_xmit() with the MAC header unset, so
eth_hdr(skb) resolves to skb->head + (u16)~0 and the read is out of
bounds: a 12-byte heap over-read that is also emitted on the wire as the
frame's outer source/destination MAC. KASAN reports a slab-out-of-bounds
read in macsec_start_xmit() on 6.0; on current mainline a CONFIG_DEBUG_NET
build flags it as an unset mac header in skb_mac_header().
On the TX path the L2 header is at skb->data, so use skb_eth_hdr(), added
by commit 96cc4b69581d ("macvlan: do not assume mac_header is set in
macvlan_broadcast()") for exactly this purpose. |
| In the Linux kernel, the following vulnerability has been resolved:
drbd: reject data replies with an out-of-range payload size
recv_dless_read() receives a P_DATA_REPLY from a peer into the bio of an
outstanding read request. The peer-supplied payload length reaches it as
the signed int data_size, and two peer-controlled inputs can make it
negative. With a negotiated data-integrity-alg the digest length is
subtracted first, so a reply whose payload is smaller than the digest
underflows data_size. With no integrity algorithm (the default) data_size
is assigned from the unsigned h95/h100 wire length and drbdd() never
bounds it for a payload-carrying command, so a length above INT_MAX casts
it negative; this path needs no non-default feature. The bio receive loop
then computes expect = min_t(int, data_size, bv_len), which is negative,
and drbd_recv_all_warn(mapped, expect) receives with a size_t of SIZE_MAX
into the first mapped page.
The sibling receive path read_in_block() is not affected: it uses an
unsigned size and rejects it against DRBD_MAX_BIO_SIZE before receiving.
Reject a data reply whose size is negative after the optional digest
subtraction, covering both triggers.
Impact: a malicious or man-in-the-middle DRBD peer copies attacker-chosen
bytes past a bio page in the receiver, corrupting kernel memory. A node
that reads from its peer (a diskless node, or read-balancing to the peer)
is exposed in the default configuration; data-integrity-alg is not
required. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing/osnoise: Call synchronize_rcu() when unregistering
This ensures that any RCU readers traversing the instance list
have finished, before releasing the reference on the tracer that
the instance points to. |
| In the Linux kernel, the following vulnerability has been resolved:
pmdomain: imx93-blk-ctrl: Extract PHY as shared domain for DSI/CSI
The MIPI DSI and CSI domains share control bits for clock and reset, which
can lead to incorrect behavior if one domain disables the shared resource
while the other is still active.
To fix the issue, introduce a shared MIPI PHY power domain to own the
common resources and make DSI and CSI its subdomains. This ensures the
shared bits are properly managed and not disabled while still in use. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rt2x00: avoid full teardown before work setup in probe
rt2x00lib_probe_dev() uses the full rt2x00lib_remove_dev() teardown for
all probe failures. However, drv_data allocation and workqueue allocation
can fail before intf_work, autowakeup_work and sleep_work have been
initialized.
Do not enter the full remove path until the probe has reached the point
where those work items are set up. Return directly for drv_data allocation
failure, and use a small early cleanup path for workqueue allocation
failure.
This issue was found by our static analysis tool and then confirmed by
manual review of rt2x00lib_probe_dev() and rt2x00lib_remove_dev(). The
early probe exits should not call a common teardown path that assumes the
later work setup has already completed.
A QEMU PoC forced alloc_ordered_workqueue() to fail before the work
initializers are reached. The resulting fail path entered
rt2x00lib_remove_dev(), and DEBUG_OBJECTS reported invalid work drains with
rt2x00lib_probe_dev() and rt2x00lib_remove_dev() in the stack. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: cyw: fix heap overflow on a short auth frame
brcmf_notify_auth_frame_rx() takes the frame length from the firmware
event and copies the frame body with the management header offset
subtracted:
u32 mgmt_frame_len = e->datalen - sizeof(struct brcmf_rx_mgmt_data);
...
memcpy(&mgmt_frame->u, frame,
mgmt_frame_len - offsetof(struct ieee80211_mgmt, u));
The only length check is e->datalen >= sizeof(*rxframe), so mgmt_frame_len
can be anything from 0 up. offsetof(struct ieee80211_mgmt, u) is 24. When
mgmt_frame_len is below that, the subtraction wraps as an unsigned value to
a huge length. The memcpy then runs far past the kzalloc'd buffer. A
malicious or malfunctioning AP can make the frame short during the
external SAE auth exchange, so this is a remotely triggered heap overflow.
Reject frames shorter than the management header offset before the copy. |
| Missing authentication for critical function in Windows Credential Guard allows an authorized attacker to perform spoofing locally. |
| Incorrect authorization in Windows Hello allows an authorized attacker to bypass a security feature locally. |
| Use after free in Windows Console Driver allows an authorized attacker to elevate privileges locally. |
| Use after free in Windows Push Notifications allows an authorized attacker to elevate privileges locally. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btrtl: validate firmware patch bounds
rtlbt_parse_firmware() copies patch_length - 4 bytes before appending the
firmware version. A malformed firmware patch shorter than the version field
can make this subtraction underflow and turn the copy into an oversized
read and write during Bluetooth setup.
The existing patch_offset + patch_length check can also wrap on 32-bit
architectures. Validate the patch length and range without arithmetic
overflow before allocating or copying the patch. |
| In the Linux kernel, the following vulnerability has been resolved:
ipvs: fix more places with wrong ipv6 transport offsets
Sashiko reports for more incorrect IPv6 transport offsets.
The app code for TCP was assuming IPv4 network header
even after the ipvsh argument was provided. This can
cause problems with apps over IPv6. As for the only
official app in the kernel tree (FTP) this problem is
harmless because we use Netfilter to mangle the FTP
ports and we do not adjust the TCP seq numbers.
Also, provide correct offset of the ICMPV6 header in
ip_vs_out_icmp_v6() for correct checksum checks when
the IPv6 packet has extension headers. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: validate EHT MLE before MLD ID read
cfg80211_gen_new_ie() copies ML probe response elements from
the parent frame when the parent EHT multi-link element has an
MLD ID matching the nontransmitted BSSID index.
The code only checked that the extension element had more than
one byte before calling ieee80211_mle_get_mld_id(). That helper
assumes a BASIC MLE with enough common info and documents that
callers must first use ieee80211_mle_type_ok().
Attack chain:
malicious AP sends a short EHT MLE in an MBSSID beacon.
cfg80211_inform_bss_frame_data() stores the copied IE buffer.
cfg80211_parse_mbssid_data() builds the nontransmitted BSS IE.
cfg80211_gen_new_ie() sees the EHT MLE in the parent frame.
ieee80211_mle_get_mld_id() then reads past the IE boundary.
Validate the MLE type and size before reading the MLD ID. This
matches the contract required by the MLE helper and rejects the
short element before any internal MLE fields are accessed. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: validate extension-frame layout before RX
Extension frames only have the extension header at the regular 802.11
header offset. The generic RX path can still reach helpers and interface
dispatch code that read regular header address fields before unsupported
extension subtypes are dropped.
mac80211 currently only handles S1G beacon extension frames. Drop other
extension subtypes before they can reach regular-header RX processing.
For S1G beacons, linearize the SKB with the management-frame path and
require the fixed S1G beacon header, including optional fixed fields
indicated by frame control, before generic RX dispatch.
Route S1G beacons through the station/default-link RX path without
regular-header station lookup. Avoid regular-header address reads in the
mac80211 RX paths that process S1G extension beacons, including
accept-frame, duplicate-detection, address-copy, and MLO
address-translation paths.
Also make ieee80211_get_bssid() length-safe before returning the S1G
source-address pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
device property: initialize the remaining fields of fwnode_handle in fwnode_init()
If a firmware node is allocated on the stack (for instance: temporary
software node whose life-time we control) or on the heap - but using a
non-zeroing allocation function - and initialized using fwnode_init(),
its secondary pointer will contain uninitialized memory which likely
will be neither NULL nor IS_ERR() and so may end up being dereferenced
(for example: in dev_to_swnode()). Set fwnode->secondary to NULL on
initialization. While at it: initialize the remaining fields of struct
fwnode_handle too just to be sure.
[ Fix typo in commit message. - Danilo ] |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: s390: pci: Fix handling of AIF enable without AISB
When a guest seeks to register IRQs without a summary bit specified,
ensure that the associated GAITE then stores 0 for the guest AISB
location instead of virt_to_phys(page_address(NULL)). |
| In the Linux kernel, the following vulnerability has been resolved:
s390/zcrypt: Fix buffer over-read in cca_cipher2protkey
Add validation of both the actual key buffer size and token length
fields in all the cca_check_sec*token() functions. Additionally check
in cca_gencipherkey() for possible underflow with returned key size.
The CCA token structures contain user-controlled len fields that
were used in operations without proper validation against both the
actual buffer size and minimum token structure size. An attacker
could set this field larger than the actual buffer size, leading to
reading beyond buffer boundaries. This may result in a kernel crash or
exposure of memory via sending this as part of a request down to the
crypto card. Also an attacker could have used a very small len value
and thus enforce a buffer under-run which may produce similar effects
as a over-read.
So now a key must
- key buf length must be at least sizeof the token struct
- the key len field inside the token must fit into the range of
sizeof key token struct ... key buf length |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: use wiphy work for socket owner autodisconnect
nl80211_netlink_notify() walks the cfg80211 wireless device list when a
NETLINK_GENERIC socket is released. If the socket owns a connection, the
notifier queues the embedded wdev->disconnect_wk work item.
That work is a plain work_struct today. NETDEV_GOING_DOWN cancels it, but a
NETLINK_URELEASE notifier that already observed conn_owner_nlportid can
queue it after that cancel returns. _cfg80211_unregister_wdev() then
removes the wdev from the list and waits for RCU readers, but
synchronize_net() does not drain work queued by such a reader.
Make the autodisconnect work a wiphy_work instead. The callback already
needs the wiphy mutex, and wiphy_work runs under that mutex. This lets
teardown cancel pending autodisconnect work while holding the mutex,
without a cancel_work_sync() vs. worker locking concern.
Also cancel the wiphy work after list_del_rcu() and synchronize_net(). Any
NETLINK_URELEASE notifier that had already reached the wdev list has then
either queued the work and it is removed, or can no longer find the wdev. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/guc: Keep scheduler timeline name alive
The scheduler keeps a pointer to the timeline name, but q->name
is freed with the exec queue while scheduler fences can still
reference it.
Store the name in struct xe_guc_exec_queue so it shares
the scheduler's RCU-deferred lifetime.
(cherry picked from commit 41075f0eb5dcbd3b065d15f15ef7bbe9315188e8) |
| In the Linux kernel, the following vulnerability has been resolved:
tipc: serialize udp bearer replicast list updates
tipc_udp_rcast_add() and cleanup_bearer() both update ub->rcast.list with
list_add_rcu() / list_del_rcu(), but nothing serializes them. The add runs
from the encap receive softirq (via tipc_udp_rcast_disc()) without
rtnl_lock(), so it can race the cleanup delete and corrupt the list:
list_del corruption. prev->next should be ffff8880298d7ab8,
but was ffff88802449ad38. (prev=ffff888027e3ec98)
kernel BUG at lib/list_debug.c:62!
RIP: __list_del_entry_valid_or_report+0x17a/0x200
Workqueue: events cleanup_bearer
Call Trace:
cleanup_bearer (net/tipc/udp_media.c:811)
process_one_work (kernel/workqueue.c:3302)
worker_thread (kernel/workqueue.c:3466)
The bearer can be enabled from an unprivileged user namespace, as the
TIPCv2 generic-netlink ops carry no GENL_ADMIN_PERM.
Add a spinlock to struct udp_bearer and take it around the list_add_rcu()
in tipc_udp_rcast_add() and the list_del_rcu() loop in cleanup_bearer() so
the two writers can no longer corrupt the list.
Reject a duplicate peer under the same lock before allocating, and remove
tipc_udp_is_known_peer(). The old lockless pre-check in
tipc_udp_rcast_disc() was racy: two softirqs discovering the same peer
could both find it absent and add it twice.
cleanup_bearer() runs from a workqueue after tipc_udp_disable() clears the
bearer's up bit, so an encap softirq can still reach tipc_udp_rcast_add()
and add a peer after cleanup_bearer() has already emptied the list, leaking
that entry when the bearer is freed. Mark the bearer disabled under
rcast_lock once the list is emptied and refuse further additions. |
