Export limit exceeded: 409268 CVEs match your query. Please refine your search to export 10,000 CVEs or fewer.
Search
Search Results (11435 CVEs found)
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2026-64361 | 1 Linux | 1 Linux Kernel | 2026-09-04 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: hfs/hfsplus: fix u32 overflow in check_and_correct_requested_length check_and_correct_requested_length() compares (off + len) against node_size using u32 arithmetic. When the caller passes a large len value (e.g. from an underflowed subtraction in hfs_brec_remove()), off + len can wrap past 2^32 and produce a small result, causing the bounds check to pass when it should fail. For example, with off=14 and len=0xFFFFFFF2 (underflowed from data_off - keyoffset - size in hfs_brec_remove), off + len wraps to 6, which is less than a typical node_size of 512, so the check passes and the subsequent memmove reads ~4GB past the node buffer. Fix this by widening the addition to u64 before comparing against node_size. This prevents the u32 wrap while keeping the logic straightforward. | ||||
| CVE-2026-85498 | 1 Polkit Project | 1 Polkit | 2026-09-04 | 3.5 Low |
| No description is available for this CVE. | ||||
| CVE-2026-64407 | 1 Linux | 1 Linux Kernel | 2026-09-04 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: Bluetooth: btnxpuart: Fix out-of-bounds firmware read in nxp_recv_fw_req_v3() During the v3 firmware download the controller sends a v3_data_req with a 32 bit offset and a 16 bit len. nxp_recv_fw_req_v3() checks only the lower bound of the offset and then sends firmware from that offset. nxpdev->fw_dnld_v3_offset = offset - nxpdev->fw_v3_offset_correction; serdev_device_write_buf(nxpdev->serdev, nxpdev->fw->data + nxpdev->fw_dnld_v3_offset, len); Nothing checks that fw_dnld_v3_offset + len stays within nxpdev->fw->size, so a controller that asks for an offset or length past the firmware image makes the driver read past the end of nxpdev->fw->data and send that memory back over UART. nxp_recv_fw_req_v1() already bounds the same write. Add the equivalent check to the v3 path, reject the request when it falls outside the firmware image, and zero len on the error path so the fw_v3_prev_sent bookkeeping at free_skb stays consistent. | ||||
| CVE-2026-73761 | 2 Hewlett Packard Enterprise (hpe), Hpe | 157 Aos-cx, Aruba Cx 10000-48y6c \(r8p13a\), Aruba Cx 10000-48y6c \(r8p14a\) and 154 more | 2026-09-04 | 6.5 Medium |
| An out-of-bounds read vulnerability exists in the underlying operating system of AOS-CX that could lead to unauthenticated information disclosure by sending a specially crafted packet. Successful exploitation of this vulnerability results in the ability to disclose sensitive information from the underlying operating system. | ||||
| CVE-2026-64330 | 1 Linux | 1 Linux Kernel | 2026-09-04 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: usb: typec: tcpm: Validate SVID index in svdm_consume_modes() In svdm_consume_modes(), the SVID value is read from pmdata->svids using pmdata->svid_index as an array index without bounds validation: paltmode->svid = pmdata->svids[pmdata->svid_index]; If pmdata->svid_index is driven beyond SVID_DISCOVERY_MAX (16), it results in an out-of-bounds read of the pmdata->svids array. Because pd_mode_data is embedded inside struct tcpm_port, indexing past svids reads into adjacent fields. In particular: - At index 16, it reads the altmodes count. - At index 18 and beyond, it reads into altmode_desc[], which contains partner-supplied SVDM Discovery Modes VDOs. By injecting a chosen SVID into altmode_desc[0].vdo and driving svid_index to 20, the partner can force paltmode->svid to be loaded with an arbitrary, partner- chosen SVID, which is then registered via typec_partner_register_altmode(). Fix this by validating that pmdata->svid_index is non-negative and strictly less than pmdata->nsvids before accessing the pmdata->svids array inside svdm_consume_modes(). | ||||
| CVE-2026-39956 | 1 Jqlang | 1 Jq | 2026-09-04 | 6.1 Medium |
| jq is a command-line JSON processor. Prior to version 1.8.2, the _strindices builtin in jq's src/builtin.c passes its arguments directly to jv_string_indexes() without verifying they are strings, and jv_string_indexes() in src/jv.c relies solely on assert() checks that are stripped in release builds compiled with -DNDEBUG. This allows an attacker to crash jq trivially with input like _strindices(0), and by crafting a numeric value whose IEEE-754 bit pattern maps to a chosen pointer, achieve a controlled pointer dereference and limited memory read/probe primitive. Any deployment that evaluates untrusted jq filters against a release build is vulnerable. This issue has been patched in commit fdf8ef0f0810e3d365cdd5160de43db46f57ed03, which is part of version 1.8.2. | ||||
| CVE-2026-84484 | 1 Nasajpl | 1 Iondtn | 2026-09-04 | 7.5 High |
| ION-DTN versions before 4.2.0 contain an out-of-bounds read vulnerability in the decodeSdnv function that allows unauthenticated remote attackers to read memory by sending truncated SDNV values. Attackers can send a UDP datagram to the LTP link service input port with a truncated SDNV to trigger reads up to nine bytes past buffer boundaries and underflow byte counters. | ||||
| CVE-2026-84640 | 1 Mozilla | 1 Thunderbird | 2026-09-03 | 7.5 High |
| A maliciously constructed mail header could lead to a one byte read past the end of a buffer. This vulnerability was fixed in Thunderbird 155, Thunderbird 140.15, and Thunderbird 153.2. | ||||
| CVE-2026-64087 | 1 Linux | 1 Linux Kernel | 2026-09-03 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: hwmon: (pmbus/adm1266) reject implausible blackbox record_count adm1266_nvmem_read_blackbox() loops over a record_count that comes straight from byte 3 of the BLACKBOX_INFO response. The destination buffer is data->dev_mem, sized for the nvmem cell's declared 2048 bytes (ADM1266_BLACKBOX_MAX_RECORDS * ADM1266_BLACKBOX_SIZE = 32 * 64). A device that reports a record_count greater than 32 -- whether due to firmware bugs, bus corruption, or a non-responsive slave returning 0xff -- would walk read_buff past the end of the dev_mem allocation on the trailing iterations. Cap record_count at ADM1266_BLACKBOX_MAX_RECORDS (introduced here) before entering the loop and return -EIO on any larger value, so a malformed BLACKBOX_INFO response cannot drive the loop out of bounds. | ||||
| CVE-2026-64347 | 1 Linux | 1 Linux Kernel | 2026-09-03 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: usb: gadget: composite: fix dead empty check in the USB_DT_OTG handler The OTG branch of composite_setup() falls back to the first configuration when none is selected: if (cdev->config) config = cdev->config; else config = list_first_entry(&cdev->configs, struct usb_configuration, list); if (!config) goto done; ... memcpy(req->buf, config->descriptors[0], value); list_first_entry() never returns NULL. On an empty list it returns container_of() of the list head. So the "if (!config)" check is dead. When cdev->configs is empty, config points at the head inside struct usb_composite_dev. config->descriptors[0] reads whatever sits at that offset. The memcpy copies up to w_length bytes of it into the response buffer. cdev->configs can be empty in two cases. One is a teardown race on gadget unbind with a control transfer in flight. The other is a driver that sets is_otg before it adds a config. A reproducer that holds cdev->configs empty triggers a KASAN fault in this branch. Use list_first_entry_or_null() so the existing check does its job. | ||||
| CVE-2026-64351 | 1 Linux | 1 Linux Kernel | 2026-09-03 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: net: usb: kalmia: bound RX frame length in kalmia_rx_fixup() kalmia_rx_fixup() computes usb_packet_length = skb->len - (2 * KALMIA_HEADER_LENGTH) as a u16, guarded only by a pre-loop check that skb->len is at least KALMIA_HEADER_LENGTH, which is 6. A device can deliver a short bulk-IN frame with skb->len in the 6 to 11 range, or leave a short trailing remainder on a later loop iteration. Either case underflows usb_packet_length to about 65530. That bypasses the usb_packet_length < ether_packet_length truncation path. The device-supplied ether_packet_length, a le16 up to 65535 read from header_start[2], then drives a memcmp() and the following skb_trim() and skb_pull() past the end of the rx buffer. The rx buffer is hard_mtu * 10, which is 14000 bytes. That is an out of bounds read. Require both the start and end framing headers to be present before subtracting them, on every loop iteration. | ||||
| CVE-2026-64339 | 1 Linux | 1 Linux Kernel | 2026-09-03 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: usb: misc: usbio: bound bulk IN response length to the received transfer usbio_bulk_msg() copies bpkt_len = le16_to_cpu(bpkt->len) bytes out of the bulk IN buffer (usbio->rxbuf, allocated with size usbio->rxbuf_len) into the caller's buffer. bpkt_len is fully controlled by the device and is only checked against ibuf_len; ibuf_len in turn is checked against usbio->txbuf_len, not against rxbuf_len: if ((obuf_len > (usbio->txbuf_len - sizeof(*bpkt))) || (ibuf_len > (usbio->txbuf_len - sizeof(*bpkt)))) return -EMSGSIZE; txbuf_len and rxbuf_len are taken independently from the bulk OUT and bulk IN endpoint wMaxPacketSize in usbio_probe(). A malicious or malfunctioning device that advertises a large bulk OUT endpoint and a small bulk IN endpoint (e.g. by claiming one of the quirk-free IDs such as the Lattice NX33U, 0x2ac1:0x20cb) therefore makes ibuf_len, and hence the device-supplied bpkt_len, exceed rxbuf_len. memcpy() then reads up to txbuf_len - rxbuf_len bytes past the end of the rxbuf slab object. The over-read bytes are handed back to the i2c layer and on to user space through i2c-dev, disclosing adjacent slab memory; with KASAN this is reported as a slab-out-of-bounds read. The number of bytes actually received is already known: act equals the URB actual_length and is bounded by rxbuf_len. Reject any response that claims more payload than was received, mirroring the existing "act < sizeof(*bpkt)" check just above. The control path (usbio_ctrl_msg()) is not affected: it uses a single buffer (ctrlbuf) for both directions, so its analogous copy can never leave the allocation. Found by code review. The out-of-bounds read was confirmed under AddressSanitizer with a faithful userspace model of usbio_bulk_msg()'s receive path (an rxbuf_len-sized buffer, the same act/ibuf_len/bpkt_len checks and the memcpy). A USB raw-gadget + dummy_hcd reproducer is also available. | ||||
| CVE-2026-64318 | 1 Linux | 1 Linux Kernel | 2026-09-03 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: partitions: aix: bound the pp_count scan to the ppe array aix_partition() reads the physical volume descriptor into a fixed-size struct pvd and then scans its physical-partition-extent array: int numpps = be16_to_cpu(pvd->pp_count); ... for (i = 0; i < numpps; i += 1) { struct ppe *p = pvd->ppe + i; ... lp_ix = be16_to_cpu(p->lp_ix); pvd points at a single kmalloc()'d struct pvd whose ppe[] member holds a fixed ARRAY_SIZE(pvd->ppe) (1016) entries, but the loop runs up to the on-disk pp_count. pp_count is an unvalidated __be16 read straight from the descriptor, so a crafted AIX image with pp_count larger than 1016 drives the loop to read pvd->ppe[i] past the end of the allocation (up to 65535 entries, ~2 MB out of bounds). The partition scan runs without mounting anything, when a block device with a crafted AIX/IBM partition table appears (an attacker-supplied image attached with losetup -P, or a device auto-scanned by udev), via msdos_partition() -> aix_partition(). Clamp the scan to the number of entries the ppe[] array can hold. | ||||
| CVE-2026-64066 | 1 Linux | 1 Linux Kernel | 2026-09-03 | 9.8 Critical |
| In the Linux kernel, the following vulnerability has been resolved: netfs: Fix netfs_read_to_pagecache() to pause on subreq failure Fix netfs_read_to_pagecache() so that it pauses the generation of new subrequests if an already-issued subrequest fails. | ||||
| CVE-2026-64069 | 1 Linux | 1 Linux Kernel | 2026-09-03 | 9.8 Critical |
| In the Linux kernel, the following vulnerability has been resolved: netfs: Fix cancellation of a DIO and single read subrequests When the preparation of a new subrequest for a read fails, if the subrequest has already been added to the stream->subrequests list, it can't simply be put and abandoned as the collector may see it. Also, if it hasn't been queued yet, it has two outstanding refs that both need to be put. Both DIO read and single-read dispatch fail at this; further, both differ in the order they do things to the way buffered read works. Fix cancellation of both DIO-read and single-read subrequests that failed preparation by the following steps: (1) Harmonise all three reads (buffered, dio, single) to queue the subreq before prepping it. (2) Make all three call netfs_queue_read() to do the queuing. (3) Set NETFS_RREQ_ALL_QUEUED independently of the queuing as we don't know the length of the subreq at this point. (4) In all cases, set the error and NETFS_SREQ_FAILED flag on the subreq and then call netfs_read_subreq_terminated() to deal with it. This will pass responsibility off to the collector for dealing with it. | ||||
| CVE-2026-64201 | 1 Ni | 1 Labview | 2026-09-03 | 7.8 High |
| There is a memory corruption vulnerability recently discovered in NI LabVIEW that may result in information disclosure or arbitrary code execution. Successful exploitation requires an attacker to get a user to open a specially crafted VI. This vulnerability affects NI LabVIEW 2026 Q3 (26.3.0) and prior versions. | ||||
| CVE-2026-64202 | 1 Ni | 1 Labview | 2026-09-03 | 7.8 High |
| There is a memory corruption vulnerability recently discovered in NI LabVIEW that may result in information disclosure or arbitrary code execution. Successful exploitation requires an attacker to get a user to open a specially crafted VI. This vulnerability affects NI LabVIEW 2026 Q3 (26.3.0) and prior versions. | ||||
| CVE-2026-64203 | 1 Ni | 1 Labview | 2026-09-03 | 7.8 High |
| There is a memory corruption vulnerability recently discovered in NI LabVIEW that may result in information disclosure or arbitrary code execution. Successful exploitation requires an attacker to get a user to open a specially crafted VI. This vulnerability affects NI LabVIEW 2026 Q3 (26.3.0) and prior versions. | ||||
| CVE-2026-64081 | 1 Linux | 1 Linux Kernel | 2026-09-03 | 8.4 High |
| In the Linux kernel, the following vulnerability has been resolved: firmware: arm_ffa: Validate framework notification message layout Framework notifications carry an indirect message in the shared RX buffer. Validate the reported offset and size before using them, reject zero-length payloads, and ensure that any non-header payload starts at the UUID field rather than in the middle of the message header. Use the validated offset and size values for both kmemdup() and the UUID parsing path so malformed firmware data cannot drive an out-of-bounds read or an oversized allocation. | ||||
| CVE-2026-64084 | 1 Linux | 1 Linux Kernel | 2026-09-03 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: hwmon: (pmbus/adm1266) cap PDIO scan in get_multiple at ADM1266_PDIO_NR adm1266_gpio_get_multiple() iterates the PDIO portion of the caller-supplied mask using for_each_set_bit_from(gpio_nr, mask, ADM1266_GPIO_NR + ADM1266_PDIO_STATUS) { ... } where ADM1266_PDIO_STATUS is the PMBus command code (0xE9, i.e. 233), not the number of PDIO pins. The intended upper bound is ADM1266_GPIO_NR + ADM1266_PDIO_NR = 25. gpiolib hands in a mask sized for gc.ngpio (= 25 bits on this chip), so the iteration walks find_next_bit() up to 242, reading up to 217 extra bits (a handful of unsigned-long words: four on 64-bit, seven on 32-bit) of whatever lives past the end of the mask in the caller's stack. Any incidental set bit in that range then drives a set_bit(gpio_nr, bits) call that writes past the end of the caller-supplied bits array too -- both out-of-bounds. Substitute ADM1266_PDIO_NR for the constant so the scan stops at the last real PDIO bit. | ||||