| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: tcpm: Validate SVID index in svdm_consume_modes()
In svdm_consume_modes(), the SVID value is read from pmdata->svids using
pmdata->svid_index as an array index without bounds validation:
paltmode->svid = pmdata->svids[pmdata->svid_index];
If pmdata->svid_index is driven beyond SVID_DISCOVERY_MAX (16), it results
in an out-of-bounds read of the pmdata->svids array. Because pd_mode_data
is embedded inside struct tcpm_port, indexing past svids reads into
adjacent fields. In particular:
- At index 16, it reads the altmodes count.
- At index 18 and beyond, it reads into altmode_desc[], which contains
partner-supplied SVDM Discovery Modes VDOs.
By injecting a chosen SVID into altmode_desc[0].vdo and driving svid_index
to 20, the partner can force paltmode->svid to be loaded with an arbitrary,
partner- chosen SVID, which is then registered via
typec_partner_register_altmode().
Fix this by validating that pmdata->svid_index is non-negative and strictly
less than pmdata->nsvids before accessing the pmdata->svids array inside
svdm_consume_modes(). |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: require source read access for duplicate extents
FSCTL_DUPLICATE_EXTENTS_TO_FILE passes the source file directly to
vfs_clone_file_range() or vfs_copy_file_range() without checking the SMB
access mask granted to the source handle. A handle opened with attribute
access can consequently be used to copy file contents into an
attacker-readable destination.
Require FILE_READ_DATA on the source handle before either VFS operation,
matching other ksmbd data-copy paths. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix UAF of struct file_lock in SMB2_LOCK deferred-lock cancellation
When a blocking byte-range lock request is deferred in the
FILE_LOCK_DEFERRED path, ksmbd registers the asynchronous work into
the connection's async_requests list via setup_async_work(). The cancel
callback smb2_remove_blocked_lock() holds a reference to the flock.
If the lock waiter is subsequently woken up but the work state is no
longer KSMBD_WORK_ACTIVE (e.g., due to a concurrent cancellation), the
cleanup path calls locks_free_lock(flock) without dequeuing the work from
the async_requests list. Concurrently, smb2_cancel() walks the list
under conn->request_lock and invokes the cancel callback, which then
dereferences the already freed 'flock'. This leads to a slab-use-after-free
inside __wake_up_common.
Fix this by restructuring the cleanup logic after the worker returns
from ksmbd_vfs_posix_lock_wait(). Move list_del(&smb_lock->llist) and
release_async_work(work) to the top of the cleanup block. This guarantees
that the async work is completely dequeued and serialized under
conn->request_lock before locks_free_lock(flock) is called, rendering
the flock unreachable for any concurrent smb2_cancel(). |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: serialize QUERY_DIRECTORY requests per file
smb2_query_dir() stores a pointer to its stack-allocated private data in
the ksmbd_file readdir_data. Concurrent QUERY_DIRECTORY requests using the
same file handle can overwrite this pointer while an iterate_dir() callback
is still using it, resulting in a stack use-after-free.
Add a per-file mutex and hold it while accessing the shared directory
enumeration state. The lock covers scan restart, dot entry state,
readdir_data setup and iteration, and response construction. This prevents
another request from replacing readdir_data.private before the current
request has finished using it and also serializes the shared file position. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: add a permission check for FSCTL_SET_ZERO_DATA
FSCTL_SET_ZERO_DATA in smb2_ioctl() destroys file data via
ksmbd_vfs_zero_data() -> vfs_fallocate(PUNCH_HOLE/ZERO_RANGE) after
checking only the share-level KSMBD_TREE_CONN_FLAG_WRITABLE, with no
per-handle access check. A handle opened with only FILE_WRITE_ATTRIBUTES
still yields an FMODE_WRITE filp (FILE_WRITE_ATTRIBUTES is part of
FILE_WRITE_DESIRE_ACCESS_LE, so smb2_create_open_flags() opens it
O_WRONLY), so the vfs_fallocate FMODE_WRITE check does not stop it; only
the missing fp->daccess gate would. Reproduced on mainline 7.1-rc7 with
KASAN by an authenticated SMB client: a FILE_WRITE_ATTRIBUTES-only handle
zeroed 4096 bytes of file data it had no FILE_WRITE_DATA right to
(6/6; a FILE_READ_DATA-only handle was correctly denied).
This is the unfixed sibling of commit cc57232cae23 ("ksmbd: fix FSCTL
permission bypass by adding a permission check for FSCTL_SET_SPARSE").
Because SET_ZERO_DATA writes data (not an attribute), require
FILE_WRITE_DATA. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: add permission checks for FSCTL_DUPLICATE_EXTENTS_TO_FILE
The FSCTL_DUPLICATE_EXTENTS_TO_FILE arm of smb2_ioctl() overwrites the
destination file's data via vfs_clone_file_range() with neither the
share-level KSMBD_TREE_CONN_FLAG_WRITABLE check nor a per-handle
fp->daccess check that the other write-bearing arms carry. A client can
overwrite destination data on a read-only share, or from a handle opened
with only FILE_WRITE_ATTRIBUTES (which still yields an FMODE_WRITE filp).
FILE_WRITE_ATTRIBUTES-only destination handle overwrote the file's data via
the clone. Add both checks, matching the FSCTL_SET_SPARSE permission fix;
require FILE_WRITE_DATA since this writes data. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: ISO: avoid NULL deref of conn in iso_conn_big_sync()
iso_conn_big_sync() drops the socket lock to call hci_get_route() and
then re-acquires it, but dereferences iso_pi(sk)->conn->hcon afterwards
without re-checking that conn is still valid.
While the lock is dropped, the connection can be torn down under the
same socket lock: iso_disconn_cfm() -> iso_conn_del() -> iso_chan_del()
sets iso_pi(sk)->conn to NULL (and the broadcast teardown path can also
clear conn->hcon on its own). When iso_conn_big_sync() re-acquires the
lock and reads conn->hcon, conn may be NULL, causing a NULL pointer
dereference (hcon is the first member of struct iso_conn).
This path is reached from iso_sock_recvmsg() for a PA-sync broadcast
sink socket (BT_SK_DEFER_SETUP | BT_SK_PA_SYNC), so the dropped-lock
window can race with connection teardown driven by controller events.
Re-validate iso_pi(sk)->conn and its hcon after re-acquiring the socket
lock and bail out if the connection went away, as already done in the
sibling iso_sock_rebind_bc(). |
| In the Linux kernel, the following vulnerability has been resolved:
dm log: fix out-of-bounds write due to region_count overflow
The local variable region_count in create_log_context() is declared as
unsigned int (32-bit), but dm_sector_div_up() returns sector_t (64-bit).
When a device-mapper target has a sufficiently large ti->len with a small
region_size, the division result can exceed UINT_MAX. The truncated
value is then used to calculate bitset_size, causing clean_bits,
sync_bits, and recovering_bits to be allocated far smaller than needed
for the actual number of regions.
Subsequent log operations (log_set_bit, log_clear_bit, log_test_bit) use
region indices derived from the full untruncated region space, causing
out-of-bounds writes to kernel heap memory allocated by vmalloc.
This can be reproduced by creating a mirror target whose region_count
overflows 32 bits:
dmsetup create bigzero --table '0 8589934594 zero'
dmsetup create mymirror --table '0 8589934594 mirror \
core 2 2 nosync 2 /dev/mapper/bigzero 0 \
/dev/mapper/bigzero 0'
The status output confirms the truncation (sync_count=1 instead of
4294967297, because 0x100000001 was truncated to 1):
$ dmsetup status mymirror
0 8589934594 mirror 2 254:1 254:1 1/4294967297 ...
This leads to a kernel crash in core_in_sync:
BUG: scheduling while atomic: (udev-worker)/9150/0x00000000
RIP: 0010:core_in_sync+0x14/0x30 [dm_log]
CR2: 0000000000000008
Fixing recursive fault but reboot is needed!
Fix by widening the local region_count to sector_t and adding an
explicit overflow check before the value is assigned to lc->region_count. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: ccp - Do not initialize SNP for ioctl(SNP_CONFIG)
Sashiko notes:
> if SEV initialization fails and KVM is actively running normal VMs, could a
> userspace process trigger this code path via /dev/sev ioctls (e.g.,
> SEV_PDH_GEN) and zero out MSR_VM_HSAVE_PA globally? Would the next VMRUN
> execution for an active VM trigger a general protection fault and crash the
> host?
Refuse to re-try initialization if SNP is not already initialized for
SNP_CONFIG.
This is technically an ABI break: before if SNP initialization failed it
could be transparently retriggered by this ioctl, and if no VMs were
running, everything worked fine. Hopefully this is enough of a corner case
that nobody will notice, but someone does, there are a few options:
* do something like symbol_get() for kvm and refuse to initialize if KVM is
loaded
* check each cpu's HSAVE_PA for non-zero data before re-initializing
* once initialization has failed, continue to refuse to initialize until
the ccp module is unloaded |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: ccp - Do not initialize SNP for ioctl(SNP_VLEK_LOAD)
Sashiko notes:
> if SEV initialization fails and KVM is actively running normal VMs, could a
> userspace process trigger this code path via /dev/sev ioctls (e.g.,
> SEV_PDH_GEN) and zero out MSR_VM_HSAVE_PA globally? Would the next VMRUN
> execution for an active VM trigger a general protection fault and crash the
> host?
The SEV firmware docs for SNP_VLEK_LOAD note:
> On SNP_SHUTDOWN, the VLEK is deleted.
That is, the initialization/shutdown wrapper here is pointless, because the
firmware immediately throws away the key anyway. Instead, refuse to do
anything if SNP has not been previously initialized.
This is an ABI break: before, this was a no-op and almost certainly a
mistake by userspace, and now it returns -ENODEV. ABI compatibility could be
maintained here by simply returning 0 in the check instead. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: ccp - Do not initialize SNP for SEV ioctls
Sashiko notes:
> if SEV initialization fails and KVM is actively running normal VMs, could a
> userspace process trigger this code path via /dev/sev ioctls (e.g.,
> SEV_PDH_GEN) and zero out MSR_VM_HSAVE_PA globally? Would the next VMRUN
> execution for an active VM trigger a general protection fault and crash the
> host?
sev_move_to_init_state() is called for ioctls requiring only SEV firmware:
SEV_PEK_GEN, SEV_PDH_GEN, SEV_PEK_CSR, SEV_PEK_CERT_IMPORT, and
SEV_PDH_CERT_EXPORT. After the firmware command, it does SEV_SHUTDOWN on
the SEV firmware. Since these commands do not require SNP to be
initialized, skip it by calling __sev_platform_init_locked() which only
initializes the SEV firmware. This way SNP is not Initialized at all, and
HSAVE_PA is not cleared.
The previous code saved any SEV initialization firmware error to
init_args.error and then threw it away and hardcoded the return value of
INVALID_PLATFORM_STATE regardless of the real firmware error. This patch
changes it to surface the underlying error, which is hopefully both more
useful and doesn't cause any problems.
Note that it is still safe to call __sev_firmware_shutdown() directly: it
calls __sev_snp_shutdown_locked(), which skips SNP shutdown if SNP was not
initialized. |
| NVIDIA Triton Inference Server for Linux contains a vulnerability where an attacker can cause uncontrolled resource consumption. A successful exploit of this vulnerability might lead to denial of service. |
| In the Linux kernel, the following vulnerability has been resolved:
ata: pata_sl82c105: fix bridge revision use-after-free
pci_get_slot() returns a referenced PCI device. Commit 44c10138fd4b
("PCI: Change all drivers to use pci_device->revision") replaced a
configuration-space read with direct access to the cached revision field,
but left that access after pci_dev_put(). The bridge may therefore be freed
before its revision is read.
Read the revision before dropping the reference. |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: fp9931: Fix VPOS/VNEG voltage selector table
The VPOSNEG_table[] mapping does not match the FP9931 datasheet.
The datasheet defines the VPOS/VNEG voltage mapping as:
00h-04h -> 7.04V (-7.04V)
05h -> 7.26V (-7.26V)
06h -> 7.49V (-7.49V)
...
28h-3Fh -> 15.06V (-15.06V)
However, VPOSNEG_table[] has two issues:
1. Selector 0x00~0x04 should all map to 7.04V (5 entries), but the
table has 6 entries of 7.04V, causing all subsequent entries to be
shifted by one position.
2. Selectors 0x29~0x3F should all clamp to 15.06V (23 entries), but
the table has only 41 entries. Any selector value above 0x28
would result in an out-of-bounds table access.
Fix both issues by removing the duplicate 7.04V entry and appending
the missing 23 clamped 15.06V entries, bringing the table to the
correct size of 64 entries (0x00~0x3F). |
| In the Linux kernel, the following vulnerability has been resolved:
ovpn: ensure socket is owned by ovpn before deref sk_user_data
Some subsystems, like BPF SOCKMAP, set sk_user_data without
actually setting the encap_type.
For this reason, we must make sure that the type is the
one ovpn expects before dereferencing sk_user_data.
Failing to do so may lead to out-of-bounds reads. |
| In the Linux kernel, the following vulnerability has been resolved:
mmc: loongson2: Fix sg iteration in data reorder functions
In ls2k0500_mmc_reorder_cmd_data() and ls2k2000_mmc_reorder_cmd_data(),
the for_each_sg() macro already iterates over the scatterlist entries,
with 'sg' pointing to the current entry. However, the code incorrectly
uses '&sg[i]' and 'sg_dma_len(&sg[i])' inside the loop, which treats
'sg' as an array base and indexes it again, leading to access of
wrong sg entries (or out-of-bounds if the list is not an array). |
| In the Linux kernel, the following vulnerability has been resolved:
pmdomain: mediatek: fix remaining %pOF after of_node_put()
scpsys_get_bus_protection_legacy() looks up several legacy bus
protection regmaps from device-tree nodes.
Two error paths put the device node before checking whether the regmap
lookup failed, but still pass that node to dev_err_probe() with %pOF on
failure. If of_node_put() drops the last reference, the later %pOF
formatting can dereference a freed device node.
Keep the node reference until after the error message has been emitted in
the infracfg and SMI lookup paths. Also drop the SMI node before
returning when the SMI phandle is missing. |
| In the Linux kernel, the following vulnerability has been resolved:
pmdomain: mediatek: mfg: initialize prev_o in mtk_mfg_attach_dev()
mtk_mfg_attach_dev() reads prev_o on the first iteration of its loop,
in "if (prev_o && prev_o->freq == o->freq)", before prev_o is assigned
at the end of the loop body. On that first iteration, evaluating prev_o
reads an indeterminate value. If it is non-NULL, the condition
dereferences a stale or invalid pointer, potentially faulting or
incorrectly skipping the first OPP.
Initialize prev_o to NULL. This matches the intent as well: there is no
previous OPP to compare against on the first iteration.
Found with Clang's -Wconditional-uninitialized. |
| In the Linux kernel, the following vulnerability has been resolved:
thunderbolt: Fix bandwidth group reservation indexing
Valid bandwidth group IDs range from 1 through MAX_GROUPS, while Group
ID 0 is reserved. tb_consumed_dp_bandwidth() uses the Group ID directly
to index its local group_reserved[] array.
The array currently has MAX_GROUPS entries, so its valid indices are 0
through MAX_GROUPS - 1. Group ID MAX_GROUPS therefore accesses one
element past the end, and the final group's reserved bandwidth is not
included when the array is summed.
Give group_reserved[] MAX_GROUPS + 1 entries so direct Group ID
indexing covers the reserved ID 0 and valid IDs 1 through MAX_GROUPS. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/log: Fix out-of-bounds read on empty message length
drm_log_draw_kmsg_record() accesses s[len - 1] to strip the trailing
newline, but len is unsigned int. If len is 0, the subtraction wraps
to UINT_MAX, causing an out-of-bounds read.
Add an early return when len is 0. |
