| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: add HE 6 GHz capability in the scan elems len
The HE 6 GHz Band Capability element is in the probe request for
every band if 6 GHz is supported, so add the size to scan_ies_len.
Otherwise, building probe request elements can fail, triggering the
WARN_ON in __ieee80211_start_scan(). |
| Use after free in Microsoft Edge (Chromium-based) allows an authorized attacker to execute code over a network. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: synaptics-rmi4 - fix GPF in suspend and resume when unbound
Transport drivers (such as rmi_i2c and rmi_spi) invoke
rmi_driver_suspend() and rmi_driver_resume() on their child rmi_dev
device during system power management events. However, transport drivers
are fully registered and operational even if the physical RMI driver
failed to bind or probe the rmi_dev device.
When rmi_driver_suspend() or rmi_driver_resume() is called on an unbound
rmi_dev, dev_get_drvdata() returns NULL. Calling rmi_disable_irq() or
rmi_enable_irq() without driver data attached causes a NULL pointer
dereference and General Protection Fault when attempting to lock
data->enabled_mutex.
Fix this by checking if driver data is attached to rmi_dev in
rmi_driver_suspend() and rmi_driver_resume(), exiting early if
no driver data is present. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: evdev - zero absinfo before partial copy in EVIOCSABS
The EVIOCSABS handler copies at most the user supplied ioctl size into
an uninitialized on-stack struct input_absinfo:
if (copy_from_user(&abs, p, min_t(size_t,
size, sizeof(struct input_absinfo))))
The size comes from _IOC_SIZE() of the ioctl command and is therefore
fully controlled by userspace. A short size leaves the trailing part of
the structure holding whatever was on the kernel stack, and the whole
structure is then stored into the device:
dev->absinfo[t] = abs;
EVIOCGABS hands that back to userspace, disclosing the stale stack
bytes. Only the resolution field is currently cleared, which covers the
legacy struct layout but not an arbitrarily short size.
Zero the structure before the copy so any part not supplied by the
caller reads back as zero. The existing resolution fixup is kept, since
it also handles a size that partially overlaps that field. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: core: Validate MODE SENSE lengths in scsi_cdl_enable()
scsi_cdl_enable() uses length fields returned by MODE SENSE to locate
the ATA feature mode page in a 64-byte stack buffer. A target can report
a total length shorter than its mode header and block descriptors. The
unsigned subtraction used for the MODE SELECT length can wrap, and the
separately computed buf_data can point beyond buf.
During automatic scan, enable is false, so the read-modify-write of
buf_data[4] can clear the low two bits of a target-selected
out-of-bounds stack byte. scsi_mode_select() can then copy up to 64
bytes from outside the buffer into the outgoing MODE SELECT payload,
disclosing stack contents to the target.
This is reachable while scanning a USB storage device that identifies as
an ATA device and advertises CDL support. No filesystem mount or
userspace access to the block device is required.
On upstream commit cee9395acd80 ("Linux 7.3-rc1"), a build-specific,
one-vCPU QEMU/Raw Gadget proof using QEMU-only multi-UDC allocator
sampling executed a fixed proof command inside the guest and created a
UID-0-owned marker during automatic enumeration, with KASLR and NX
enabled.
The issue was independently found during security research at Drivesec
S.r.l.
Cap the available length to the buffer size. Validate and consume the
mode header and block descriptor lengths before using the page, and
require the five bytes needed to access the CDL field. |
| In the Linux kernel, the following vulnerability has been resolved:
dma-buf: Fix silent overflow for phys vec to sgt
In case MMIO size is bigger than 4G and peer2peer DMA goes
through host bridge, we trigger a code path that assigns the
total linked IOVA (which is greater than 4G) to mapped_len.
Previously, `mapped_len` was declared as 32-bit `unsigned int`.
When accumulating `size_t` lengths, this leads to a silent wrap-around.
This truncation causes truncated lengths to be passed to functions
like `fill_sg_entry()`.
Fix this by changing `mapped_len` to `size_t` (64-bit). While
at it, fix similar potential overflow issues in `calc_sg_nents`
by using `check_add_overflow()` for `nents` and using
`unsigned int` for the loop iterator in `fill_sg_entry` to match. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: only group hidden BSSes with beacon entries
When a probe response for an unknown BSS comes in, __cfg80211_bss_update()
looks for an existing entry with the same BSSID and a hidden (zero-length
or NUL-filled) SSID, and if it finds one it groups them, using the beacon
IEs from the existing entry.
But that could find another entry without a beacon, if it was also from a
probe response (with SSID), so there's a group without beacon elements.
If a beacon with a hidden SSID for that BSSID arrives later,
cfg80211_combine_bsses() goes looking for the probe response entries that
belong to it - i.e. entries with the same BSSID and channel that have no
beacon IEs - and finds those two. They are already grouped with each
other, so it hits its
WARN_ON_ONCE(bss->pub.hidden_beacon_bss)
WARN_ON_ONCE(!list_empty(&bss->hidden_list))
which are there because an entry without beacon elements is not supposed
to be part of a group yet.
Only combine entries when a beacon was already received, ones that are
kept separate will be combined when a beacon arrives. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: cyw: pass PMKID to firmware if present
Zero out auth_status on initialization. Otherwise, garbage will
leak from the stack to the firmware (when ssid is less than 32 bytes
and/or when params->pmkid is set). Then, pass the params->pmkid to the
firmware (without it, the firmware caches a garbage PMKID on successful
authentication and denies a subsequent association request that includes
the PMKID). |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: restrict BAR0 fallback read to SR-IOV VFs only
The BAR0 fallback read path was introduced as a workaround for SR-IOV VFs
where the VRAM aperture is not available during early init. Restrict this
workaround to only SR-IOV VFs where it's needed.
(cherry picked from commit d8a0affd207c813bd063fa2c27786f449eaf92b8) |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: Intel: avs: Fix unbalanced module reference count
strace_open() invokes try_module_get() which on success takes
the module reference. If any follow up operation causes
strace_open() to fail, the refcount shall be put down. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: Intel: avs: Refactor and fix init_config access
Existing code accesses enties found in ->init_configs array through
indexes that are part of ->config_ids array. Those two are limited by:
->num_init_configs and ->num_config_ids respectively. Using ID larger
or equal to ->num_init_configs leads to out-of-bounds access:
avs_path_module_send_init_configs()
loop:
(...) &acomp->tplg->init_configs[ids[i]]
^ out-of-bounds candidate
Rather than adding another if-statement, refactor the code. There is no
need to store the IDs, have a list of pointers to actual config-entries
instead. As the verification of ->init_config entries does not differ from
verification of other types that are part of the topology.c file, simply
reuse the code. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/vma: correctly unaccount on mmap_prepare() failure
__mmap_setup() accounts memory for relevant mappings via:
security_vm_enough_memory_mm()
-> __vm_enough_memory()
-> vm_acct_memory()
If __mmap_setup() fails, this indicates that this accounting did not take
place, and thus it's appropriate for __mmap_region() to jump to
abort_munmap.
However if call_mmap_prepare() fails, it also jumps there and any accounted
memory is not correctly unaccounted.
Fix this by handling each error separately. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix the possible bioc_list memory leak during error
There are two possible ways to leak bioc memory on
btrfs_ordered_extent::bioc_list:
- An error occurred for btrfs_insert_one_raid_extent()
Then the function btrfs_insert_raid_extent() immediately return
without freeing any bioc in the bioc_list.
- An ordered extent hit an IO error
In that case the ordered extent will have BTRFS_ORDERED_IOERR set, and
skip the call on btrfs_insert_raid_extent() completely.
Fix the problem by:
- Introduce a new helper, btrfs_cleanup_ordered_bioc_list()
Which will remove all bioc from the bioc_list, and release the bioc.
- Call the above helper for btrfs_insert_raid_extent()
So that the cleanup helper is always called no matter what.
- Call the above helper for btrfs_finish_one_ordered()
This is called just before the final release on the ordered extent.
This was reported by Sashiko when reviewing another patch. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: fix rmmio iounmap skipped on device removal
amdgpu_pci_remove() calls drm_dev_unplug() before fini_sw(), so
drm_dev_enter() is already false there and the iounmap() guarded by it
is skipped. This .remove path runs on both hot-unplug and plain rmmod,
so the register BAR ioremap mapping leaks one instance per unload.
Unmap rmmio unconditionally (guard only on non-NULL) and drop the now
unused idx.
(cherry picked from commit dd6f86a97260e5207d3329ad03aa89fdad61b1e6) |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: refuse to make a monitor active when it has no queue
A monitor interface only gets a TXQ if it's created active, and one can't
be added later. Setting the flag on a down interface is still allowed, so
the driver is handed a monitor with no queue. ath9k dereferences it:
BUG: kernel NULL pointer dereference, address: 0000000000000066
RIP: 0010:ath_tx_node_init+0x49/0x170 [ath9k]
ath9k_add_interface+0x10c/0x140 [ath9k]
drv_add_interface+0x54/0x250 [mac80211]
ieee80211_do_open+0x32f/0x800 [mac80211]
Reached with CAP_NET_ADMIN by "iw dev X set monitor active" followed by
"ip link set X up". RTNL is held, so netlink operations block behind it.
Refuse the flag when there is no queue to give. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: avoid out-of-bounds read for empty PREQ elements
ieee80211_mesh_preq_size_ok() derives the location of the PREQ bottom
fields before checking whether the element contains even the fixed
header. ieee80211_mesh_hwmp_preq_get_bottom() reads the flags byte to
account for the optional Address Extension field. Consequently, an
empty PREQ element causes a one-byte read beyond its declared payload.
Move the helper call after both size checks, so the bottom fields are
only accessed when they are present. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mwifiex: validate scan response extents
mwifiex_ret_802_11_scan() subtracts the fixed response fields and the
firmware-provided BSS length from resp->size without first proving that
either extent fits. A short response or oversized BSS length can
therefore underflow tlv_buf_size and make the TLV parser walk beyond the
command response.
Compute the fixed extent from the selected normal or background scan
response. Validate that the fixed fields and BSS data fit before deriving
the TLV extent and entering the parser. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: zero ff_effect before compat copy in input_ff_effect_from_user
In the compat path input_ff_effect_from_user() aliases the caller's
native struct ff_effect with the smaller struct ff_effect_compat and
copies only the compat sized prefix:
compat_effect = (struct ff_effect_compat *)effect;
if (copy_from_user(compat_effect, buffer,
sizeof(struct ff_effect_compat)))
The tail of the native structure is never written. Callers pass an
uninitialized on-stack object, for example evdev_do_ioctl() for
EVIOCSFF, so those bytes keep their previous stack contents.
input_ff_upload() then stores the full native structure in
ff->effects[id], from where a uinput based force feedback daemon can
read it back via UI_BEGIN_FF_UPLOAD, disclosing kernel stack memory to
userspace.
Zero the effect before the compat copy. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: rmi_smbus - fix out-of-bounds read in rmi_smb_write_block()
When chunking writes into SMBus blocks in rmi_smb_write_block(), the
loop calculates block_len using the original total length (len) instead
of the remaining length (cur_len).
If len is greater than 32 bytes (SMB_MAX_COUNT), block_len remains 32
for every iteration, even on the final partial chunk where fewer than 32
bytes remain. This causes smb_block_write() to read 32 bytes from the
advanced data buffer pointer, reading past the end of the input buffer.
Fix this by calculating block_len using cur_len and advancing the buffer
and address pointers by block_len. |
| In the Linux kernel, the following vulnerability has been resolved:
mmc: mxcmmc: cancel data work and watchdog on remove
mxcmci_remove() frees the host through the devm tail, but neither it nor
mmc_remove_host() drains the driver's own asynchronous state.
host->watchdog, a 10 s timer armed on the DMA path in mxcmci_setup_data(),
is deleted only by the DMA- and IRQ-complete paths, which the remove path
does not explicitly drain; it can therefore fire after the host is freed
and dereference it in mxcmci_watchdog(). host->datawork, armed from the
IRQ handler on the PIO path, is not cancelled by the remove path either.
Free the devm-registered IRQ, then cancel datawork and delete the watchdog
in mxcmci_remove(), before dma_release_channel(). Freeing the IRQ first
keeps a trailing handler from re-arming datawork between the cancel and
the host free. Both callbacks are non-self-rearming.
This issue was found by an in-house static analysis tool. |
